38
Just bought an emergency 2003 Camry, has anyone owned one?
Truck has shit the bed.
I needed something that would get me to the next town over every day for work for the next few months.
I’m trying really hard to get out of debt so as much as I wanted to just bite the bullet and get a newer, decent, vehicle I ended up buying a junker.
190k miles. Runs okay. Sounds rough but no knocking or ticking. The exhaust has just been jb welded in a few places (which is probably what that weird smell was). Bearing is going out in one of the pulleys.
Brake pedal sinks pretty low before the brakes start to grab. Is this typical for this model?
Anything I need to look out for?
Comments
None of that is typical for that year model Camry. That is typical of a car that has not been well maintained and is nearing end of life. 190k mileage is a lot, even for a Toyota. To correct these issues will cost money. That’s just how it is with old cars.
My wife’s 1999 Camry Solara has 366,000 miles on it and I would drive it cross country without reservations. Also it is constantly breaking and I’m constantly fixing it. It’s usually little stuff but, yeah, it’s old.
If it’s rough at Idle and dies if you don’t give it a bit of pedal on cold days check the Idle air control and get a can of carb and intake cleaner and a toothbrush (one that is due for replacement from brushing your teethis perfect.) Have someone to keep it running or manipulate the throttle body by hand when it’s running.
Take the intake hose from the air cleaner off the throttle body, with it off and out of the way open the intake butterfly wide and you will likely see the backside is black. Look for some passages that come off of the front side, these will go towards an idle bypass or Idle air control passage. There is often a valve that will move in and out to keep the engine at Idle when your foot is off the throttle, over time crud can build up and make the valve stick and/or restrict the passages. Start it up and let run for a couple minutes. Then do the spray carb cleaner in the passages and keep it running dance… either a person in the vehicle or you using your hand on the butterfly need to keep it running. Around 1500 to 2000 rpm works generally well, have them try to keep it there, and listen to the sound. It should be steady, give a short test spray and it will kinda sputter. The longer the spray more it will sputter, the goal is to hose the passages down and clean out the crud. This is pretty much universal for all fuel injected vehicles.
Edit for addition. Pull the Idle air control valve and clean it with the toothbrush and some cleaner.
‐–‐-------------------
Another trick is to find a vacuum port you can borrow for a bit. You can often find one that is about a 1/4 inch. You get some cheap aquarium air line and medium sized glass of water 10 to 12 ounces or so. Have the stuff to do an oil change as well since a little water can pass the rings. Hook up a Tee if needed for easy access to the vacuum port. Go for a drive till the engine is fully warmed, a hot day is best but above 60 F is fine. Park it, leave it running, take your cup of water and play the keep it running dance while dipping the line in the water for a second. Do this every few seconds, something like a 1 second drink and 5 seconds out till about 2/3 of the water is gone. At that point let rest of the water go in. Ideally let it die right at the end but as soon as possible shut it off. Then let it sit for 10 minutes. Start it up and go for a spirited drive. The water will flash turn to steam inside the engine cleaning some carbon deposits out, if you do a lot of short drives or stop and go traffic this can help keep it clean. You can use up to 10% alcohol in the water if you want, the yellow booties of heat is what you are looking for, keep it mixed up well!!!
It’s an old school top engine cleaner. I learned about it in shop class while in high school. While working in a shop the shop owner had a nice caddy come in that was driven to church twice a week about 10 blocks by an older couple. They decide to go on a trip one day to visit family after a couple years of short trips. It came in knocking and clunking. Ran the top engine cleaner through and delivered it back purring like a kitten.
If you want to use the store oil based stuff like seafoam, go for it.
You can run larger oil filters, use a cross reference web site and you will find that a lot of filters are the same threads and base size or really close but longer. Also works on lawn mowers, I use a NAPA 1764 on my 19hp Briggs and Stratton riding mower. Yes you need to look up some specs for the bypass but most are within a few psi.
-------‐--------
Change the plugs, check the air filter, do a couple oil changes 1000 miles apart. Rotate the tires and maybe get them balanced. Look at the brake pads!!! If it’s drum rear they can wait, the majority of your braking ability comes from the front. Disc breaks are a simple repair. By the parts from rock auto. Seriously, Amazon is a pain and you will likely need rock auto to use as a reference if you multiple parts for the same thing do a VIN search with the manufacturer. They will do it for free and give you a breakdown of the exact build. You can run rotors that have a little damage with minimal issue. A small grove will seat after a month or so, it’s not going to hurt the pads, things will wear a little bit faster till that point, you will lose next to nothing. Grooves deeper than a fingernail thickness, a sandpaper like texture or a visible taper need turned, head to O’Reilly auto, have them take a look, they charge a few bucks to turn. Most shops with a machine to turn rotors will do it as well for 10 or 15 bucks. They may be too thin and need replaced or too cheap not to replace, 75 bucks will get you a powerstop kit with pads and rotors. 140 gets you drilled and slotted rotors with pads.
Check the bushings if they are cracked they need replaced ASAP. Check the half shaft CV boots… if they are tore replace the boots!!! Have someone drive it and turn a circle around you as tight as possible then go straight after a second if there is a clicking when turning the CV joints need replaced the half shafts from Moog run about 65 bucks each, it takes two.
I know I’m including a lot of info on things you may never do this stuff yourself but knowing what to check and the cost of parts can save you a ton. Private shops will generally allow you to source your own parts if you have them already but call first.
I’ve rebuilt the entire front end running gear in my pickup myself. If you can change plugs, oil, and brake pads you can do a rebuild and stringline align the front end. Look up the video’s. And look around a few times before you start. Even if the car is junk keeping things repaired it’s cheaper on liability than a new car on full coverage with a payment. I have a 2003 4.7l Dakota I bought for 5000 cash in 2013 or 14. I drive it without any worry.
A cheap OBD2 Bluetooth adapter and something like Torque and you can troubleshoot anything. Find a website for owners or your vehicle and lurk. Learn from what they have already done, bet there is a few people who are keeping cars running like new on there.
What a fantastic amount of information. I appreciate you writing all that out! I’m taking notes
All those 2000s Toyotas sound kinda rough tbh. They are chain driven OHC timing sets and out of the 6 or so I’ve seen/worked on, most of them rattle and clank a concerning amount. if youre used to quiet belt driven Hondas or pushrod American engines it takes getting used to.
Excessive noise at startup usually indicates the timing tensioner is worn though, and may need a camera inspection, so keep an ear out for that.
For shaking roughness the usual tuneup suspects are first. Spark plugs help, get OEM ngk brand. Fix exhaust leaks at the manifold, and replace the upstream oxygen sensor, this will get the ECU fuelling the engine correctly again. Change the oil, and check it every tank of gas for oil consumption. Put in a couple cans of sea foam at next gas station fill up.
Definitely check out the ATF and change it if it is automatic. Mid 2000’s Toyota transmissions tend to have issues when neglected and often don’t get the atf changed enough.
For the brakes, do a visual inspection first. Jack up and remove tires. Check front and back pads/rotors/calipers for leaks, wear level, and uneven wear. Check rear drums (assuming it is a 4cyl model with rear drums) for wheel cylinder fluid leaks inside, worn shoes, or broken hardware.
Generally, a long travel/mushy pedal is caused by the brake master cylinder wearing out its bore, causing the piston seals to not hold fluid until it’s partially depressed. It also happens if someone has been in there fucking with the brake system and did not properly bleed all the air out, or a caliper/wheel cylinder has failed and is leaking. If visual inspection comes up all OK I would flush the brake system with fresh fluid yourself (ez bleed kit is $10 and lots of guides exist on YouTube etc) and see if performance improves. If not, order a master cylinder from RockAuto.
Thanks for all the info. Appreciate the detail!
Of course, glad to help! Feel free to ask follow ups as you learn more I’m always happy to keep shitboxes on the road.
The cost of tools often is about the same as getting the job done. Look up videos on how to fix stuff and you end up with a bunch of tools Ao that the next job is super discounted. My socket set is now close to 35 years old and has saved me easily thousands of dollars.
Is the 10mm socket also 35 years old?
You know it’s not
Believe it or not, I do still have the original 10mm. It’s a Craftsman set back from when they made quality tools. Probably worth more now than when I bought it.
Now that’s some solid advice. Thanks!
Ah, mechanic special. All those issues could be resolved for not much money if you are mechanically inclined, and that bitch should last you another 190k
That’s kind of what I was banking on. They say a well maintained Toyota will often hit 300k.
Still, buying a used car is just trading a set of problems you know for ones you don’t.
I’ve had vehicle problems for the last 3 years, I don’t know why I just did this to myself again. Oh well, roll those bones, I guess.
Decades ago I bought a Toyota at 100k miles, being a poor student.
Still ran fine at 300k when I traded it in, and I treated it badly, rarely did oil changes, etc.
That’s encouraging
I also have treated Toyotas like shit and they have never failed me
Do basic maintenance and youre good for 10+ more years
I’ll treat her like the love of my life. Which isn’t saying much but at least she’ll get an oil change somewhat on schedule.
She prefers, “lady of the road.”
Literally for the streets.
Rough sounding engine can be a lot of things, but you could check the easy stuff such as air filter and vac hoses. Are any of the rubber hoses connected to the intake area cracked or damaged? Also, check fuel filter if you can find it.
Spark plugs might also be worth a check, just remember to connect the leads correctly afterwards, or the firing sequence will be off.
Cool, appreciate it!
Rough idle in mine (different car) was a cracked air intake hose, the ribbed part between the air filter and the engine. Gently pull the ribbed part to look into the low spots.
I swear by a product called auto-Rx. Add it to the oil or ATF and it slowly breaks down any sludge. Not saying that model has issue, just general advice. There’s also something called Cataclean which helps clean the catalytic converter if you think there’s any issue.
I’ll have to check those out, thanks!
Check your oil usage.
If it is burning oil, or has a leak and needs top-ups, keep an eye on the level regularly.
I seized one, after it drank to much oil on a road trip. Gauge past H, cooked.
–
Also, get a tissue box to complete the look.
https://www.youtube.com/watch?v=4J2YoBKqHNw
Good to know, and sorry for your loss
I’d go even further and just change the oil and filter. Doesn’t cost much compared to how much your car will enjoy it, but mainly to check filter and old oil for sparkly bits, I.e. metal shavings.
Do the brake engage hard when pressed or kinda weak and spongey?
About in the middle. They don’t feel quite as soft as a lot of air in the line but they’re not aggressive when they grab either. Long distance to the floor, though.
I’m about to go pick it up for the drive back to the house, so if you never hear from me again we know what happened.
Sounds like worn discs, then. Easy to replace, can usually be done with basic tools, and doesn’t cost that much either. Might as well replace the pads while you’re at it.
Went to go pick it up after hours, got in it and halfway down the block the check engine light came on. Lol, classic
I’ve had several of these, all worked fine. Get an app for your phone to read it and it’ll spit engine codes and a LOT more.
Get it scanned! $10 says it’s emissions or evap related and can safely be ignored at least until your next registration period (if you have inspections) or whenever you get a chance to unfuck the exhaust.
Generic obd2 readers are cheap, I use a Bluetooth one from eBay and the Torque Pro app on my phone.
I just bought one off of a coworker the other day. Some Chinese brand I’ve never heard of but it’s bi-directional so that’s a plus. Used to have a pretty nice Autel but lately I, too, just used a cheap Bluetooth before I gave it to a friend. I’ll post back here tomorrow after I’ve scanned it so we can see how good your betting predictions are. 😁
Good luck and I hope I’m right, most things I see of this age usually have codes for evap/emissions and if the exhaust is as fucked as you say, I guarantee the cat is probably not working and setting its own cel.
What’d it say?
Dunno. I’m not getting out of bed to go check. I’ll post the results when the rooster crows.
I believe these might be the generation that experiences oil consumption so I’d keep an eye on the oil level for a while until you know for sure.
Alright, I’ll do that. Thank you
Also !mechanicadvice@lemmy.world
If it makes noise, you should probably get it fixed. It shouldn’t be very expensive, especially if you can do it yourself.
Source: bought a 2005 Camry and drive it 160k miles in 17 years and only sold it because we didn’t have room to park it after getting a different type of vehicle. It was still in great shape, and I do miss it.
Right on
Sign in to comment. Sign in