Skip to content

Comment on Just bought an emergency 2003 Camry, has anyone owned one?

You are viewing one comment and its replies. View all comments

Comments

  • @MuttMutt@lemmy.world· · edited

    If it’s rough at Idle and dies if you don’t give it a bit of pedal on cold days check the Idle air control and get a can of carb and intake cleaner and a toothbrush (one that is due for replacement from brushing your teethis perfect.) Have someone to keep it running or manipulate the throttle body by hand when it’s running.

    Take the intake hose from the air cleaner off the throttle body, with it off and out of the way open the intake butterfly wide and you will likely see the backside is black. Look for some passages that come off of the front side, these will go towards an idle bypass or Idle air control passage. There is often a valve that will move in and out to keep the engine at Idle when your foot is off the throttle, over time crud can build up and make the valve stick and/or restrict the passages. Start it up and let run for a couple minutes. Then do the spray carb cleaner in the passages and keep it running dance… either a person in the vehicle or you using your hand on the butterfly need to keep it running. Around 1500 to 2000 rpm works generally well, have them try to keep it there, and listen to the sound. It should be steady, give a short test spray and it will kinda sputter. The longer the spray more it will sputter, the goal is to hose the passages down and clean out the crud. This is pretty much universal for all fuel injected vehicles.

    Edit for addition. Pull the Idle air control valve and clean it with the toothbrush and some cleaner.

    ‐–‐-------------------

    Another trick is to find a vacuum port you can borrow for a bit. You can often find one that is about a 1/4 inch. You get some cheap aquarium air line and medium sized glass of water 10 to 12 ounces or so. Have the stuff to do an oil change as well since a little water can pass the rings. Hook up a Tee if needed for easy access to the vacuum port. Go for a drive till the engine is fully warmed, a hot day is best but above 60 F is fine. Park it, leave it running, take your cup of water and play the keep it running dance while dipping the line in the water for a second. Do this every few seconds, something like a 1 second drink and 5 seconds out till about 2/3 of the water is gone. At that point let rest of the water go in. Ideally let it die right at the end but as soon as possible shut it off. Then let it sit for 10 minutes. Start it up and go for a spirited drive. The water will flash turn to steam inside the engine cleaning some carbon deposits out, if you do a lot of short drives or stop and go traffic this can help keep it clean. You can use up to 10% alcohol in the water if you want, the yellow booties of heat is what you are looking for, keep it mixed up well!!!

    It’s an old school top engine cleaner. I learned about it in shop class while in high school. While working in a shop the shop owner had a nice caddy come in that was driven to church twice a week about 10 blocks by an older couple. They decide to go on a trip one day to visit family after a couple years of short trips. It came in knocking and clunking. Ran the top engine cleaner through and delivered it back purring like a kitten.

    If you want to use the store oil based stuff like seafoam, go for it.


    You can run larger oil filters, use a cross reference web site and you will find that a lot of filters are the same threads and base size or really close but longer. Also works on lawn mowers, I use a NAPA 1764 on my 19hp Briggs and Stratton riding mower. Yes you need to look up some specs for the bypass but most are within a few psi.

    -------‐--------

    Change the plugs, check the air filter, do a couple oil changes 1000 miles apart. Rotate the tires and maybe get them balanced. Look at the brake pads!!! If it’s drum rear they can wait, the majority of your braking ability comes from the front. Disc breaks are a simple repair. By the parts from rock auto. Seriously, Amazon is a pain and you will likely need rock auto to use as a reference if you multiple parts for the same thing do a VIN search with the manufacturer. They will do it for free and give you a breakdown of the exact build. You can run rotors that have a little damage with minimal issue. A small grove will seat after a month or so, it’s not going to hurt the pads, things will wear a little bit faster till that point, you will lose next to nothing. Grooves deeper than a fingernail thickness, a sandpaper like texture or a visible taper need turned, head to O’Reilly auto, have them take a look, they charge a few bucks to turn. Most shops with a machine to turn rotors will do it as well for 10 or 15 bucks. They may be too thin and need replaced or too cheap not to replace, 75 bucks will get you a powerstop kit with pads and rotors. 140 gets you drilled and slotted rotors with pads.

    Check the bushings if they are cracked they need replaced ASAP. Check the half shaft CV boots… if they are tore replace the boots!!! Have someone drive it and turn a circle around you as tight as possible then go straight after a second if there is a clicking when turning the CV joints need replaced the half shafts from Moog run about 65 bucks each, it takes two.

    I know I’m including a lot of info on things you may never do this stuff yourself but knowing what to check and the cost of parts can save you a ton. Private shops will generally allow you to source your own parts if you have them already but call first.

    I’ve rebuilt the entire front end running gear in my pickup myself. If you can change plugs, oil, and brake pads you can do a rebuild and stringline align the front end. Look up the video’s. And look around a few times before you start. Even if the car is junk keeping things repaired it’s cheaper on liability than a new car on full coverage with a payment. I have a 2003 4.7l Dakota I bought for 5000 cash in 2013 or 14. I drive it without any worry.

    A cheap OBD2 Bluetooth adapter and something like Torque and you can troubleshoot anything. Find a website for owners or your vehicle and lurk. Learn from what they have already done, bet there is a few people who are keeping cars running like new on there.

    7
    • What a fantastic amount of information. I appreciate you writing all that out! I’m taking notes

      1

Sign in to comment. Sign in