If it’s rough at Idle and dies if you don’t give it a bit of pedal on cold days check the Idle air control and get a can of carb and intake cleaner and a toothbrush (one that is due for replacement from brushing your teethis perfect.) Have someone to keep it running or manipulate the throttle body by hand when it’s running.
Take the intake hose from the air cleaner off the throttle body, with it off and out of the way open the intake butterfly wide and you will likely see the backside is black. Look for some passages that come off of the front side, these will go towards an idle bypass or Idle air control passage. There is often a valve that will move in and out to keep the engine at Idle when your foot is off the throttle, over time crud can build up and make the valve stick and/or restrict the passages. Start it up and let run for a couple minutes. Then do the spray carb cleaner in the passages and keep it running dance… either a person in the vehicle or you using your hand on the butterfly need to keep it running. Around 1500 to 2000 rpm works generally well, have them try to keep it there, and listen to the sound. It should be steady, give a short test spray and it will kinda sputter. The longer the spray more it will sputter, the goal is to hose the passages down and clean out the crud. This is pretty much universal for all fuel injected vehicles.
Edit for addition. Pull the Idle air control valve and clean it with the toothbrush and some cleaner.
‐–‐-------------------
Another trick is to find a vacuum port you can borrow for a bit. You can often find one that is about a 1/4 inch. You get some cheap aquarium air line and medium sized glass of water 10 to 12 ounces or so. Have the stuff to do an oil change as well since a little water can pass the rings. Hook up a Tee if needed for easy access to the vacuum port. Go for a drive till the engine is fully warmed, a hot day is best but above 60 F is fine. Park it, leave it running, take your cup of water and play the keep it running dance while dipping the line in the water for a second. Do this every few seconds, something like a 1 second drink and 5 seconds out till about 2/3 of the water is gone. At that point let rest of the water go in. Ideally let it die right at the end but as soon as possible shut it off. Then let it sit for 10 minutes. Start it up and go for a spirited drive. The water will flash turn to steam inside the engine cleaning some carbon deposits out, if you do a lot of short drives or stop and go traffic this can help keep it clean. You can use up to 10% alcohol in the water if you want, the yellow booties of heat is what you are looking for, keep it mixed up well!!!
It’s an old school top engine cleaner. I learned about it in shop class while in high school. While working in a shop the shop owner had a nice caddy come in that was driven to church twice a week about 10 blocks by an older couple. They decide to go on a trip one day to visit family after a couple years of short trips. It came in knocking and clunking. Ran the top engine cleaner through and delivered it back purring like a kitten.
If you want to use the store oil based stuff like seafoam, go for it.
You can run larger oil filters, use a cross reference web site and you will find that a lot of filters are the same threads and base size or really close but longer. Also works on lawn mowers, I use a NAPA 1764 on my 19hp Briggs and Stratton riding mower. Yes you need to look up some specs for the bypass but most are within a few psi.
-------‐--------
Change the plugs, check the air filter, do a couple oil changes 1000 miles apart. Rotate the tires and maybe get them balanced. Look at the brake pads!!! If it’s drum rear they can wait, the majority of your braking ability comes from the front. Disc breaks are a simple repair. By the parts from rock auto. Seriously, Amazon is a pain and you will likely need rock auto to use as a reference if you multiple parts for the same thing do a VIN search with the manufacturer. They will do it for free and give you a breakdown of the exact build. You can run rotors that have a little damage with minimal issue. A small grove will seat after a month or so, it’s not going to hurt the pads, things will wear a little bit faster till that point, you will lose next to nothing. Grooves deeper than a fingernail thickness, a sandpaper like texture or a visible taper need turned, head to O’Reilly auto, have them take a look, they charge a few bucks to turn. Most shops with a machine to turn rotors will do it as well for 10 or 15 bucks. They may be too thin and need replaced or too cheap not to replace, 75 bucks will get you a powerstop kit with pads and rotors. 140 gets you drilled and slotted rotors with pads.
Check the bushings if they are cracked they need replaced ASAP. Check the half shaft CV boots… if they are tore replace the boots!!! Have someone drive it and turn a circle around you as tight as possible then go straight after a second if there is a clicking when turning the CV joints need replaced the half shafts from Moog run about 65 bucks each, it takes two.
I know I’m including a lot of info on things you may never do this stuff yourself but knowing what to check and the cost of parts can save you a ton. Private shops will generally allow you to source your own parts if you have them already but call first.
I’ve rebuilt the entire front end running gear in my pickup myself. If you can change plugs, oil, and brake pads you can do a rebuild and stringline align the front end. Look up the video’s. And look around a few times before you start. Even if the car is junk keeping things repaired it’s cheaper on liability than a new car on full coverage with a payment. I have a 2003 4.7l Dakota I bought for 5000 cash in 2013 or 14. I drive it without any worry.
A cheap OBD2 Bluetooth adapter and something like Torque and you can troubleshoot anything. Find a website for owners or your vehicle and lurk. Learn from what they have already done, bet there is a few people who are keeping cars running like new on there.
You just gotta keep coming back around to the project till it’s finished. I have multiple going and weather, injuries, and time sometimes get in the way. I’m not a roof person (i keep 3 points of contact at all times) and did it in sections by doing a 20X25 foot tear off, pull nails, repair, sheathing, underlay, and shingle.
It’s not easy but the alternative is paying someone more than I like. My house is approximately 50X30 feet with an 8/12 pitch roof. Approximately 22 square in size. My cost was about 6k total with the sheathing I probably would have been charged 25 to 30K by a company.
I had one person as ground help. Got smart and stuck him in the upstairs to pass shingles through the gaps in the slats before I covered them instead of trying to carry them on the ladder.
I’m going to tear the rotten back porch off the house at some point and rebuild it completely. The roof was built at too shallow of an angle and it is rotten, same for some spots in the floor. It was originally an exposed porch that was covered and walled in. So many issues… Eventually will be replacing the rubblestone foundation as it’s falling apart, may put in a basement while I’m at it.
I replaced an entire roof myself. Tore off 4 layers of roofing, fixed the rotten 1x4 slats that the cedar shake roof was on, sheathed the roof deck, applied the underlayment, and shingled the roof.
All the old roofing went out in three trash cans that were fully loaded every week. One was ours, the other two were neighbors cans who are generally gone and used with their permission.
There are a few other houses in town where they have been trying to DIY their roof as well. They are not doing so well…
I feel your pain. Had to let my buddy go a couple years ago. He kept me going when my wife passed.
Rascal was laying on the bed one day. I touched his nose and said, “Beep.” He just sat there. I did it again and he had a little lip curl. Again and it was a little bigger. Again and he really showed some teeth. Final time he snapped my finger, it was more of a “I got ya, now what?” He didn’t even apply any pressure. He knew we were just playing.
Any time a woman would sneeze he would bark at them. Not just one or two little barks but all out barking.
He would try and play with my bowling ball, he would grab it with his front legs and roll it around.
He loved snow but rarely got to see it. Said many times I wanted to take him somewhere with deep snow so he could dive in…
I could point my finger at him say “bang” and he would play dead. Many times he would be laying on his side barking and I would tell him, “dead dogs don’t bark” then say bang again and he would quit.
Dog tax…
https://lemmy.world/pictrs/image/ae19b7ac-e5bd-4205-9b95-6ea4569735e7.jpeg
We have been building layers of security for years. CDN’s can quickly block lots of things https://www.ioriver.io/blog/cdn-security-risk
If I was a security researcher and found an issue my first call would be the developer, my second would be some top CDN’s so they can search for and mitigate traffic in web applications.
Edit. I should also add docker and fast updating. I just updated everything I Run with internet exposed ports in about 20 minutes.
I buy most of my clothing from clearance racks for less than 10 bucks per item. I usually have to shorten pants a few inches as I’m short in the legs and long in the torso. I do it myself because investing cash into alterations on a cheap pair of pants isn’t worth it to me.
You could get similar (and in some ways faster as routing is better with fast single cores) performance with an X10SLL-F, Xeon E3-1271V3, 16GB of RAM and an Intel X520 10G NIC.
Power draw will be higher with a maximum around 110 watts vs 55 for the DEC 850 v2 but that is only under full load, the real world load will be around 45 watts vs 30 watts.
You can easily increase the ram in the Supermicro motherboard, as well as put in multiple 10G NIC’s or even faster. Throw a couple mirrored SSD’s (the Intel D3-S4510’s are amazing) and drop it into a case with a psu and you can be up and running for around 300 to 400 through eBay, the mobo and cpu is running 80 bucks together.
NVME drive in a router isn’t worth much, outside of boot time and logs it just sits there. Even a HDD is fine for that, a SATA SSD will boot in about 30 seconds after POST. I’m using the X10SLL-F with an E3-1226 v3, 16GB of RAM, and a pair of D3-S4510’s that are underprovioned. I do not have native IPv6 and use a Wireguard tunnel to Route64, multiple vLAN’s, run CrowdSec with Intrusion Detection and UnboundDNS beyond the base system on a 1Gbps fiber connection WAN with 10Gbps fiber backbone LAN.
OpnSense is truthfully meant to be managed through the GUI or the API. If you want to control through a CLI you may find building a system on FreeBSD with packages is better. The tools used are mostly things in the FreeBSD pkg system and can be recreated, the OpnSense setup is mainly a GUI, an API, and some middleware that makes everything work. I’ve been using OpnSense since 15.7, I tried multiple others before then including running Openwrt on a WRT54G IMHO the DEC850 is way overpriced so unless you are running this for a business you will probably be better suited with some used server hardware
I’m a bare metal guy when it comes to routers.
With that said you are fretting over something that probably won’t matter and that is the ethernet port speed. Your current router only has gigabit ports and the router can only pass data from the LAN to the WAN at speeds fast enough to saturate your internet connection speeds. The only advantage of 2.5gbps on the router would be IF you are running multiple vLAN’s. Since you are already using the router as a point for your switch to connect to the internet you are already limited to 1Gbps speeds.
Install OpnSense on the device you have available, set it up for the basics (DHCP reservations, IP addresses for the LAN, etc.), change the ip address in the original router to something that will work with your new setup and turn off the DHCP server. Then do some testing with your new router and see what you think. The old router will work as an ok access point and switch for now, grab a cheap switch to expand if you need to since the WAN port on the archer will no longer be usable.
Later on when you have some extra cash you can grow and expand where you feel the need. I’m using 10Gbps for my backbone with 1Gbps Dell 5548 PowerConnect switches for the majority of devices. You can get the PowerConnect switches on ebay for around 50 to 100 bucks easily. Most clients don’t need more than 1Gbps (even 4k cameras) and a 10Gbps card dropped in your server will give you great speeds for cheap. An Intel X520 10G NIC can be picked up for 30 bucks add a couple sfp+ modules for about 10 each plus an OM3 fiber cable for a few bucks and you are set for a while. If you get a Dell PowerConnect 5548P (the P makes it a POE switch) and you can power POE cameras and POE access points without anything extra and still use the rest of they’re ports for regular computer connections.
ZFS rollbacks only have to roll back the changed files so it’s a pretty quick process unless there were some major changes.
Yeah, that was the goal with the D3’s. I’m trying to get things to the point where if I’m no longer able to handle things that the router will stay updated and be simple to repair for my family.
I keep config backups of the config as well but my boot drive is a pair of mirrored Intel D3-S4510’s that are underprovioned by 50GB.
Rollback time will technically depend on the size of the change since a rollback only replaces changed files so that will depend on how far back you are rolling back to. My largest snapshot references about 2GB and is a little over 4 months old, I would estimate about 5 minutes at most rolling back to that point.
0 points on What is the most unbelievable thing that you have (technically) done? in !asklemmy@lemmy.world ·
< Crazy. For real. I’ve been told. Hard to disagree.
For vacations I aim for 80 feet under water.
I want to start a non profit too.